|
Yang Peiran, et al
Analysis of transient rheological thermal elastohydro-dynamic
lubrication in line
contacts……………………………………………………………………………………… (1-001)
Shi Jinyuan
Reliability design of steam turbine blades
……………………………………………………………………… (1-009)
Sun Qinghong, et al
A study of the new isolation technique impact vibration
……………………………………………………… (1-016)
Ding Linpu, et al
Effect of cooling condition on solidification characteristics
of heavy ductile iron casting
…………………………………………………………………………………… (1-024)
Chen Guoding, et al
Thermal analysis for partial elastohydrodynamic lubricated
line contacts under highload………………………………………………………………………………………(1-030)
Li Zhe
The amplitude-frequency response and balancing of the shaking force
and shaking moment of elastic
linkages …………………………………………………………………………
(1-038)
Liu Dongxing, et al
Anisotropic yield criterion considering
J3……………………………………………………………………… (1-044)
Luo Weiliang, et al
An NC auto-programming method for free form surfaces………………………………………………………
(1-051)
Li Xijing, et al
Determination of thermophysical properties of materials
using regularization
gradient algorithm for solving inverse problems…………………………………………………………………
(1-059)
Yu Shangzhi, et al
Development of transistor-inverter arc welding power
source—mathematic analysis
of the working process
of high-frequency transformer and output
reactor………………………………………(1-065)
Wang Shuren, et al
Theory and application
on the relief grinding of ZC1 wheel hob
……………………………………………… (1-074)
Zhou Min, et al
Optimum design of side turning rotor type overspeed
control
mechanism of horizontal axis wind turbing……………………………………………………………………… (2-083)
Jia Jun, et al
The solidification of immiscible alloy
in orthogonal electromagnetic
field……………………………………… (2-090)
Liang Xizhi, et al
Experimental investigation of air-separator
of axial fan………………………………………………………… (2-095)
Chen Fang, et al
Measurement and research of the cupola's
realistic procedural melting zone……………………………………
(2-102)
Song Yong, et al
Tribological behavior of carbon fibre-Pb
alloy matrix
composites ………………………………………………(2-108)
Guo Jianting, et al
Relationship between high temperature mechanical properties
of polycrystall Ni, Al alloy and boron content …………………………………………………………………(2-113)
Deng Jingliu, et al
The dynamic behavior of pump-controlled reversing process
in hydraulic closed-circuit
……………………………………………………………………………………… (2-119)
Ling Jing, et al
Two-dimensional method of fatigue reliability analysis
and design …………………………………………… (2-126)
Sun Shuming, et al
hydrogen distribution
model at crack tip in Ni-single crystals …………………………………………………
(2-136)
Feng Yuntian, et al
Analysis of Low Order Resonance and Computation
of critical running speed for elastic linkages………………………………………………………………………(2-142)
Yu Youting
Energy blance of the dilute solid-gas two-phase flow……………………………………………………………(2-150)
Lu Changhou, et al
A study of new model bearing—a three spiral oil
wedge hydrodynamic
bearing ………………………………(3-160)
Yu S Y, et al
Reseach on the process of the chip Formation
for engineering ceramices ………………………………………(3-168)
Sun Sheng, et al
The reverse simulation technique of die forging based
on UBET and its
application……………………………(3-177)
Fan Zijie, et al
Component mode synthesis for dynamic analysis
of flexible
manipulator arms with viscoelastic damping
…………………………………………………………………… (3-182)
Wu Hanchen, et al
The application of the theory of gear meshing
to conjugate cam mechanism…………………………………… (3-192)
Feng Zhiyou, et al
Kineto-elastodynamic analysis of four-bar linkages incorporating
the effects of clearances in kinematic pairs
………………………………………………………………………(3-202)
Zhou Weixian
Prediction of right-side curves in forming limit diagram
of a sheet metal-part I: predicting
fundamentals…………………………………………………………………(3-207)
Zhou Weixian
Prediction of right-side curves in forming limit diagram
of a sheet metal-part Ⅱ: predicting method ……………………………………………………………………
(3-215)
Wu Yuchen, et al
Microstructure and wear resistance of electroless deposited
nickel-phosphorus alloy coatings
……………………………………………………………………………… (3-224)
Wang Huaming, et al
Abrasion resistance behaviour of austenite-bainitic
ferrite dual-phase
steels…………………………………… (3-230)
Zhu Xianhua, et al
Numerical simulation on the formation of botton cone
of inclusions in large steel ingots…………………………………………………………………………………
(3-235)
Shen Huanxiang, et al
The superplasticity of aluminium-copper cast alloy
with rare-earth element……………………………………(3-242)
Sun Jun, et al
Stress triaxiality levels and charscteristics of void growth………………………………………………………
(4-247)
Li Yan, et al
A study on mathematical model of welding seam tracking
with vision signal in robotic welding ……………………………………………………………………………
(4-254)
Xi Daoyan, et al
Technology and equipment of water-constricted air plasma
cutting of spiral pipes welded on line……………………………………………………………………………
(4-261)
Yang Yusheng, et al
A method of calculation of the proper blank
for deep drawing
parts of anisotropic sheet
metal………………………………………………………………………………… (4-267)
Zhao Jiansheng, et al
Rigid ball indentation method for testing brittleness
of surface treatment layer…………………………………(4-274)
Peng Yunke, et al
Qptimal design of principle parameters
for a disk cam
mechanism with oscillating roller
follower……………………………………………………………………… (4-282)
Yang Tingli, et al
General approach for choice of quasi-velocities
for simplifing dynamic
equation of constrained mechanical systems……………………………………………………………………
(4-289)
Wang Songnian, et al
Function of particle size distribution and calculation
criterion of
reliability of lubricating state in rubbing
pairs……………………………………………………………………(4-303)
Mo Jianhua, et al
Experimental investigation on elastohydrodynamic lubrication
of oil-in-water emulsions…………………………………………………………………………………………(4-312)
Shi Feng, et al
Numerical calculations of gas-solid two-phase flow
in curved ducts…………………………………………… (4-319) |