A TEHD analysis of a disc-supported, double-layer, point-pivoted,
thrust bearing of a hydraulic generator……………………………………………………………………………(1-001)
Huang Ping, et al

Influence of real roughnesses on pressure distributions and
film shapes in elastohydrodynamic lubrication ………………………………………………………………… (1-009)
Zhang Zhiming, et al

Effects of pad and pivot elastic deformations on tilting
pad bearing and rotor system dynamic behavior…………………………………………………………………(1-015)
Wei Jianjun, et al

Effects of additive chemistry on the friction and wear properties of a Cr₂O₃ coating ………………………… (1-025)
Zhang Huatang, et al

Friction and wear behavior of surface fusing coatings and functions of the rare additive ……………………… (1-032)
Gao Runshen, et al

Cyclic bonding strength for hard coatings and the effect of residual stresses ……………………………………(1-039)
Cao Lili, et al

Qualitative correlation between the transition of lubrication
regimes and chemical structure of lubrication film……………………………………………………………… (1-045)
Dong Junxiu, et al

On Action mechanism of some non-active antiwear agents………………………………………………………(1-053)
Zhang Siwei

Application of systems analysis to improving the wear
characteristics of drilling rigs' brake pairs ……………………………………………………………………… (1-060)
Hu Yuanzhong

A dynamic system model for running-in and its applications……………………………………………………(1-069)
Zhou Yingsheng, et al

Analyses of scuffing mechanism of sliding lubricated line contacts …………………………………………… (1-078)
Li Wenhui, et al

Automatic identification of freedom types of planar kinematic chains………………………………………… (2-087)
Qin Datong, et al

Study on tooth modification of hourglass worm gearing with developable tooth surface……………………… (2-094)
Liang Xichang, et al

Special profile shaper…………………………………………………………………………………………… (2-099)
Liu Zhubai, et al

Physical simulation of tension stress theory of a rigid-plastic
mechanical model for upsetting a circular cylinder……………………………………………………………… (2-102)
Liu Hongmin, et al

Comprehensive experiment study of the force parameters of cold strip rolling a 4-h Mill………………………(2-106)
Wang Yongjie, et al

Algorithm for face/polyhedron classification in machine design CAD system ………………………………… (2-113)
Lin Guocheng, et al

Analysis on deformation and stress of bow spring with nonlinear theory ………………………………………(2-119)
Yao Yingxue, et al

In-process detection of tool wear and breakage in turning……………………………………………………… (2-125)
Wang Jiaxun, et al

Calculation of spinning force by the elastoplastic finite element method……………………………………… (2-131)
Nie Shaomin, et al

Complex stress analysis of cold mill roll…………………………………………………………………………(2-138)
Huang Changhua, et al

Elastohydrodynamic lubrication of long elliptical contacts under heavy load……………………………………(2-145)
Correspondent of this journal

Further breakthrough made in research on mechanical theory and
forming law of superplastic deformation…………………………………………………………………………(2-153)
Chen Weimin, et al

Optimum design for stiffness and damping ratios of liquid
dampers used in forging hammers ……………………………………………………………………………… (3-159)
Wu Shenglin, et al

Study on control of twin-hydraulic-motor synchrodrive system ……………………………………………… (3-165)
Luo Shoujing, et al

Research on the deforming load of liquid extrusion………………………………………………………………(3-171)
Shimpachi Yazawa, et al

Loosening of bolt-nut connection induced by reciprocating
tangential load applied to clamped plates ……………………………………………………………………… (3-176)
Heiji Sugita, et al

Development of isothermal-transformed steel wire for non-heat treated bolts………………………………… (3-183)
Fang Rurong, et al

Double substructure method in stress analysis of screw threads with interference fit………………………… (3-190)
Wang Liandong, et al

Solution of generalized slip-line for upsettinga cylinder
(H/D＞1) between flat platens ………………………………………………………………………………… (3-195)
Huang Tianming, et al

New method of gear cutting………………………………………………………………………………………(3-204)
Wu Anping, et al

Analysis of contact property of double enveloping tooth profile
and squeeze characteristics between tooth surfaces …………………………………………………………… (3-210)
Liu Fei, et al

Study on energy flow models of mechanical transmission systems …………………………………………… (3-215)
Fan Xun, et al

Multi-grid solution to reynolds equation in hydrodynamic lubrication
of dynamically loaded journal bearings ………………………………………………………………………… (3-220)
Peng Donglin, et al

Error analysis on a new method for pulse signal subdivision…………………………………………………… (3-226)
Zhang Xiangwei

Simulation of an uneven road surface and vehicle vibration
based on the filtered poisson process…………………………………………………………………………… (3-230)
Wang shuxin, et al

Dynamics of multibody system including kinematic and force constraints …………………………………… (4-237)
Ma Shuzhi, et al

Linear formulation of input torque for spatial linkages …………………………………………………………(4-246)
Fan Yujian, et al

Investigation of in-process measurement of geometric features for machine parts………………………………(4-251)
Chen Lixin, et al

Prediction of vibration and noise of gear box …………………………………………………………………… (4-257)
Li Hongren, et al

Multi-stage adaptive control for the electrohydraulic servo system …………………………………………… (4-261)
Li Li et al

Discrimination and forecast of machine working condition………………………………………………………(4-267)
Tang Chaowei, et al

Study on laser measuring device for 3-D curved surfaces ……………………………………………………… (4-273)
Lai Kewei, et al

Concurrent design system based on the concept of design/manufacturing feature……………………………… (4-278)
Chen Zhuoru, et al

Optimum design and dynamic simulation of double-pocket bearing friction pairs
between eccentric crankshaft and connecting rod in crankshaft piston motors ………………………………… (4-285)
Zhang Guanghui, et al

Study on the rolling cone enveloping hourglass worm gearing ………………………………………………… (4-293)
Du Zeyu, et al

Microcomputer image processing for dynamic distribution
of diffusible hydrogen in welded zone of alloyed steel ………………………………………………………… (4-299)
Zhang Shichang, et al

Multi-axes curved surface cutter grinding machine basedon motions composition principle…………………… (4-304)
Yan Xiangan, et al

Research on the method of fault tree in mechanical control systems…………………………………………… (4-310)
Li Runfang, et al

Numerical analysis for sealing system in reactor pressure vessel flanges ……………………………………… (4-319)
Zhang Zhenchun, et al

Study on extrusion-upsetting combined technique……………………………………………………………… (4-323)